Answer first: the GDW1000 is a tri-band FDD repeater that simultaneously amplifies Band 8 (900 MHz, uplink 890-915 MHz / downlink 935-960 MHz), Band 3 (1800 MHz, uplink 1710-1785 MHz / downlink 1805-1880 MHz) and Band 1 (2100 MHz, uplink 1930-1990 MHz / downlink 2110-2180 MHz). Band 8 carries 2G GSM voice and SMS for O2 and Vodafone, Band 3 carries 4G LTE data for EE and Three, and Band 1 carries 3G UMTS data fallback for every UK network. The unit provides at least 60 dB of uplink gain and at least 65 dB of downlink gain per band, outputs at least 27 dBm at the MS port, covers 1000 m², supports 100 users, and is UKCA and CE certified for Ofcom licence-exempt use. The honest limit: O2 and Vodafone 4G data runs on Band 20 at 800 MHz, which the GDW1000 does not amplify, so O2 and Vodafone customers receive boosted 2G voice and 3G only.

This guide explains, frequency by frequency, what each band does in the UK, which operators and MVNOs ride on it, how the uplink and downlink pairs work, why the ≥60 and ≥65 dB gain figures and the ≥27 dBm output ceiling matter for a 1000 m² commercial site, why a tri-band box beats the dual-band GD1000 and GW1000, what VoLTE means for Three and EE calls, and exactly where the GDW1000 stops helping. Read this before ordering if your main complaint is slow O2 or Vodafone 4G, because that service sits outside the GDW1000's three tuned bands.

Quick Answer: What Do Band 8, Band 3 and Band 1 Actually Do in the GDW1000?

The numbered facts below are the technical summary; the sections that follow open each band in full, with the frequency pairs, network mapping, gain numbers and the honest coverage limit.

• Band 8 at 900 MHz (uplink 890-915 MHz, downlink 935-960 MHz) carries 2G GSM voice calls and SMS for O2 and Vodafone across rural and suburban UK, with EE still carrying 2G fallback in many regions. Low frequency bends around hills and walls best.
• Band 3 at 1800 MHz (uplink 1710-1785 MHz, downlink 1805-1880 MHz) carries EE and Three 4G LTE data in towns and cities, the layer that turns one-bar 4G into a stable video call and card-terminal session.
• Band 1 at 2100 MHz (uplink 1930-1990 MHz, downlink 2110-2180 MHz) carries 3G UMTS data fallback for all four networks and remains the only data layer in many rural commercial spots.
• Gain: ≥60 dB uplink, ≥65 dB downlink per band; output power capped at ≥27 dBm maximum under the licence-exempt rules, higher than a 500 m² unit because the 1000 m² footprint needs more delivered output.
• Networks covered: EE, BT Mobile, ASDA Mobile, Virgin Mobile, Orange, T-Mobile, The People's Operator on the full stack; Three, iD, Smarty, Plusnet, Freedom Pop on 4G plus 3G; O2, Vodafone and their MVNOs on 2G voice plus 3G only.
• Why tri-band wins: the GD1000 covers Band 8 + Band 3 and misses 3G; the GW1000 covers Band 8 + Band 1 and misses 4G; the GDW1000 covers all three in one box at 1000 m² and 100 users.
• VoLTE: EE and Three 4G calling rides Band 3, so boosting Band 3 also improves those calls; O2 and Vodafone voice stays circuit-switched 2G on Band 8.
• Honest limit: O2 and Vodafone 4G uses Band 20 at 800 MHz rural and Band 7 at 2600 MHz urban; the GDW1000 does not amplify either, and neither does it touch 5G.

Band 8 (900 MHz): 2G GSM Voice and SMS for O2, Vodafone and EE Fallback

Band 8 is the 900 MHz cellular allocation. The GDW1000 tunes its uplink stage to 890-915 MHz, where the phone transmits to the tower, and its downlink stage to 935-960 MHz, where the tower transmits back. This paired FDD arrangement keeps talking and listening on separate frequencies at all times, and it is the band that holds a voice call where data cannot reach.

Who uses Band 8 for what

In the UK, O2 and Vodafone carry the bulk of their circuit-switched 2G voice calls and SMS on Band 8 at 900 MHz. Even in 2026, when smartphones default to 4G, a dropped or unregistered 4G session still falls back to the 2G GSM layer to hold a voice call, and emergency calls in weak coverage often register on 2G first. EE also broadcasts 2G on 900 MHz in many regions as a fallback beneath its 4G. For a rural pub, farm shop or village office, Band 8 is often the only layer that makes a phone call possible at all.

Why 900 MHz travels further

Lower frequency bends around terrain and penetrates brick and stone better than 1800 or 2100 MHz. Over the same distance, 900 MHz free-space path loss is roughly 10 to 12 dB lower than 2100 MHz, and building penetration in stone cottages and thick commercial walls averages 6 to 10 dB better. That is why rural voice coverage maps rely on Band 8 even where 4G has not arrived, and why the GDW1000's ≥65 dB downlink gain on this band reaches rooms that 1800 MHz waves cannot, including cellars and rear store rooms.

What the GDW1000 adds on Band 8

With a ≥60 dB uplink gain stage, a phone that transmits too weakly to reach the tower from inside the building gets a boosted return path through the Yagi; with ≥65 dB downlink gain, the tower's incoming voice signal arrives at four bars instead of zero. The output stays within the ≥27 dBm licence-exempt ceiling so the boosted cell does not desense the donor tower, and the higher gain budget of the 1000 m² unit carries the call through more internal walls than a smaller box.

Band 3 (1800 MHz): EE and Three 4G LTE Data and VoLTE

Band 3 sits at 1800 MHz. The GDW1000 uplinks on 1710-1785 MHz and downlinks on 1805-1880 MHz. In UK towns and cities this is the urban capacity band where EE and Three carry most of their 4G LTE data, and it is the band customers notice most as faster browsing, smoother video calls and reliable card payments.

EE 4G on Band 3

EE uses Band 3 as a primary urban and suburban 4G LTE carrier for browsing, video calls, streaming and VoLTE calls. An EE customer whose office kitchen shows one bar at -110 dBm turns a speed test into a session that stalls at 1 to 3 Mbps; after the GDW1000 boosts Band 3 with ≥65 dB downlink gain, the same room holds a stable LTE link in the 10 to 30 Mbps range the donor signal allows. The EE MVNOs that ride this layer include BT Mobile, ASDA Mobile, Virgin Mobile, Orange, T-Mobile and The People's Operator, all of which benefit automatically because the booster amplifies the radio band rather than a branded SIM.

Three 4G on Band 3

Three has no 2G GSM network in the UK at all, so every Three call and data session rides 4G or 3G. Band 3 carries Three's 4G LTE, and because Three voice uses VoLTE over that same 4G channel, boosting Band 3 directly improves Three call quality rather than leaving voice on a separate legacy band. iD Mobile, Smarty, Plusnet and Freedom Pop ride the Three network and benefit identically, which matters in a mixed-SIM workplace where staff may hold any of those contracts.

Capacity versus range

Band 3 carries more simultaneous data sessions per cell than Band 8 because 1800 MHz allocations are wide and modern LTE modulations are efficient, but the shorter wavelength penetrates buildings less well. This is precisely why indoor EE and Three users see strong bars on the pavement and almost none upstairs or in a rear warehouse: the wave reaches the outside wall, then loses 15 to 25 dB through brick, foil insulation, steel cladding and floor slabs. The GDW1000 intercepts that wave outside with the Yagi and re-radiates it indoors through the panel, bypassing wall loss entirely across the 1000 m² footprint.

Band 1 (2100 MHz): 3G UMTS Fallback Across All Four Networks

Band 1 sits at 2100 MHz. The GDW1000 uplinks on 1930-1990 MHz and downlinks on 2110-2180 MHz. This is the 3G UMTS layer that every UK operator still maintains as a fallback where 4G is congested, absent or weak, and it is the band a dual-band unit drops when it omits the third chain.

Why 3G still matters in 2026

EE, O2, Vodafone and Three all keep Band 1 3G switched on for areas outside 4G coverage, for devices that have not attached to LTE, and as a data bridge when the 4G cell is full. In rural villages, along valley roads and in new-build developments still awaiting 4G rollout, Band 1 at 2100 MHz is often the only data layer available at all. Without it, a phone shows signal for calls but cannot load a web page, a booking confirmation or a maps link.

Who benefits most

O2 and Vodafone customers on this unit rely on Band 1 for data, because their 4G lives on Band 20 and Band 7 outside the GDW1000 tuning. Three uses Band 1 as the fallback when Band 3 is congested at peak trading. EE uses it as a secondary data layer. One band therefore serves all four networks, which is why dropping Band 1 from a dual-band unit creates a gap every operator feels somewhere in the building.

Propagation trade-off

At 2100 MHz the wavelength is shortest of the three and building loss highest, reaching 22 to 32 dB through solid stone or steel-clad walls. The 8 dBi Yagi's directional gain and the ≥65 dB downlink budget recover a band that a whip antenna cannot reach, which is why the GDW1000 pairs the panel indoors with the Yagi outdoors rather than relying on a simple omni. For a 1000 m² commercial building, that recovered Band 1 keeps a secondary data link alive in the far corner where Band 3 fades.

Uplink and Downlink Frequencies: FDD Duplex Explained

FDD, frequency division duplex, means talking and listening happen on different frequencies at the same time. Each band the GDW1000 amplifies carries a paired uplink channel the phone uses to transmit and a downlink channel the tower uses to transmit. The table lists every pair exactly as tuned, and these boundaries are fixed by national spectrum allocation.

The uplink gap and downlink gap are fixed by national spectrum allocation; the repeater never transmits outside these pairs. Note that downlink frequencies sit above uplink frequencies in every pair, which keeps the donor filter and server filter on each band isolated from each other inside the chassis. Separating the two paths inside the box, and physically separating the Yagi from the panel outside the box, are the two layers that prevent oscillation. The ≥60 dB uplink gain matters because phones transmit at very low power; without it, a phone barely reaches the tower and the call drops even when the incoming signal sounds loud.

Which UK Networks and MVNOs Use Which Band

Because the GDW1000 amplifies the radio band rather than a branded SIM, every MVNO riding a covered network benefits automatically. The table maps each operator group to the services it receives on this unit, which is the quickest way to check whether your household or staff mix fits the kit.

O2 and Vodafone 4G data appears in the table as not covered on Band 3 because those carriers send rural and suburban 4G on Band 20 at 800 MHz and urban 4G on Band 7 at 2600 MHz, neither tuned here. This is the single most important honesty point in the guide: an O2 customer whose complaint is slow 4G, rather than dropped calls, should not expect the GDW1000 to fix that data speed.

Gain ≥60 dB Uplink, ≥65 dB Downlink and ≥27 dBm Output Power

Gain and output power are different numbers and both appear on the spec sheet for a reason. Gain is how many decibels the amplifier multiplies the signal; output power is the legal ceiling the boosted signal leaves the box at. The GDW1000's numbers sit above a 500 m² unit because a larger footprint must deliver more signal power at the panel edge.

Why uplink gain is ≥60 dB and downlink gain ≥65 dB

Downlink gain, ≥65 dB, lifts the tower's signal arriving at the Yagi up to a usable indoor level across more walls and a larger floor area. Uplink gain, ≥60 dB, lifts the phone's weak transmit back toward the tower. Uplink gain sits slightly lower than downlink gain by design because phones transmit at limited power and over-boosting the return path could desense the donor receiver; keeping the two balanced avoids oscillation that extra uplink gain would invite. The gain figures are per band, and the tri-band architecture splits the RF chain across three filters, so per-band gain sits below a single-band specialist that can reach 70 dB on one frequency.

What ≥27 dBm maximum output means

Twenty-seven dBm is roughly 500 milliwatts of conducted output at the MS port, the Ofcom-legal ceiling for this licence-exempt class at the commercial footprint rating. The AGC holds the unit at or below this figure automatically; there is no manual gain dial to crank up. Higher declared output on uncertified imported units often means oscillation risk and potential enforcement, whereas the GDW1000's fixed ceiling protects neighbours and complies with UKCA and CE marking even when 100 users attach.

How gain converts to bars and speed across 1000 m²

Building loss across a 1000 m² stone, cavity-wall or steel-clad commercial site typically consumes 45 to 65 dB between the Yagi position and the farthest room. A ≥65 dB downlink gain budget absorbs that loss with margin left for a -97 to -105 dBm donor reading to arrive indoors at a comfortable -75 to -90 dBm. A donor weaker than -110 dBm leaves no margin, which returns us to the outdoor survey point, and beyond the panel's reach a second radiating point rather than more gain is the answer.

Why Tri-Band Beats the Dual-Band GD1000 and GW1000 at 1000 m²

The GD1000 covers Band 8 + Band 3 (calls plus 4G, no 3G). The GW1000 covers Band 8 + Band 1 (calls plus 3G, no 4G). The GDW1000 covers Band 8 + Band 3 + Band 1 in one chassis, all rated at 1000 m². The comparison below shows what each unit leaves on the table for a mixed-operator site.

Buying both a GD1000 and a GW1000 to cover the missing bands means two amplifiers, two indoor panels, and two donor feeds near each other, which invites oscillation between units and doubles the installation work across a 1000 m² site. The GDW1000 folds the three chains into one box sharing a single Yagi and a single AGC, which is the core tri-band advantage: one donor feed, one power supply, one warm-up scan, and every service layer covered for the operators that appear in your household or workplace.

VoLTE: How 4G Calling Works on EE and Three

VoLTE, voice over LTE, places a phone call inside the 4G data channel instead of a legacy 2G circuit. EE and Three operate VoLTE, so a call on those networks travels Band 3 alongside data, which means boosting Band 3 improves call clarity just as it improves download speed. There is no separate voice band to amplify on EE and Three.

O2 and Vodafone voice still circuit-switched

O2 and Vodafone voice calls remain circuit-switched 2G on Band 8 even when the phone shows a 4G icon for data. On the GDW1000 that split is fine: Band 8 boost holds the call, Band 1 boost holds fallback data, and the missing Band 20 4G gap does not interrupt a voice call, it only limits data speed. This is why a business on O2 still gets clear calls from the boosted unit even though its 4G data speed is unchanged.

What this means for mixed-SIM workplaces

An office with one EE user on Band 3 data and VoLTE, one Three user on Band 3 plus Band 1 fallback, and one O2 user on Band 8 calls plus Band 1 data works as a single-booster scenario precisely because the three bands each carry the service that user actually uses. A dual-band GD1000 would leave the O2 user's 3G unsupported; a GW1000 would leave the EE and Three 4G unsupported, and neither gap can be patched by a stronger antenna alone.

Ofcom Licence-Exempt Operation, UKCA and CE Certification

The GDW1000 carries UKCA and CE certification and falls under Ofcom's licence-exempt repeater framework, which means no frequency application, no annual spectrum fee and no certified installer are required to operate it in a residential or small-business setting. The certification depends on the fixed ≥27 dBm output ceiling, the internal AGC that prevents oscillation, and the tuned band pairs staying within the 890-915, 935-960, 1710-1785, 1805-1880, 1930-1990 and 2110-2180 MHz boundaries.

Why uncertified imports carry risk

Generic units tuned to US cellular bands, or units with a manual gain dial past the legal ceiling, can interfere with neighbouring cells and attract Ofcom enforcement. The GDW1000's closed RF design, per-band AGC and marked output keep it inside the licence-exempt envelope, and the same rules govern its 1000 m² rating and 100-user headroom rather than a commercial distributed antenna system that would need a licence.

Certification and operating envelope

The unit operates from -10°C to +55°C, which covers outdoor Yagi climates and indoor cupboard placement alike, and the AC 100-240 V 50/60 Hz adapter steps down to DC 5 V for the chassis. Certification marks appear on the product listing and packaging; retain the box paperwork for warranty and any future Ofcom enquiry, and do not modify the band filters or output ceiling after purchase.

Honest Limitation: O2 and Vodafone 4G Uses Band 20 at 800 MHz and Band 7 at 2600 MHz, Not Covered

If your primary complaint is slow O2 or Vodafone 4G data rather than dropped calls, a Band 20 800 MHz specialist booster is the correct tool, not the GDW1000. Equally, the GDW1000 does not support 5G, which in the UK uses Band n78 at 3.5 GHz, NR-encoded Band n1 at 2.1 GHz with new radio encoding, and Band n28 at 700 MHz on selected rural sites; none of these decode on this unit. It also does not replace a 4G home broadband router, because the booster improves the phone's cellular link rather than supplying a dedicated fixed-wireless data service.

Who should still buy the GDW1000

The GDW1000 suits mixed-operator households and small offices where the pain list combines dropped O2 or Vodafone calls, slow EE or Three indoor 4G, and missing 3G fallback on Band 1 across the building. It suits a 1000 m² footprint with up to 100 simultaneous users, one 8 dBi Yagi outdoors, and one or two 5 dBi panels indoors. It does not suit a pure O2/Vodafone 4G-data buyer, a 5G router buyer, or a building needing more than 100 concurrent sessions.

Coverage, Users and the Antenna Kit for 1000 m²

The tuned bands sit inside a physical system rated for up to 1000 m² of indoor coverage and up to 100 simultaneous users. The kit pairs the 8 dBi weatherproof Yagi outside with a 5 dBi panel inside, a 10 m outdoor low-loss coax extendable to 20, 30, 40 or 50 m, a 5 m indoor low-loss coax with N-type connectors, and the DC 5 V UK 3-pin adapter. The ≥65 dB downlink gain per band, the ≥60 dB uplink gain and the ≥27 dBm output together deliver even coverage across a large detached home, a village shop with flat above, or a small light-commercial office hall.

Where a 1000 m² footprint splits into separated zones, an extra panel on the MS output extends coverage to a second room set rather than stretching gain past its design. The 100-user rating counts active sessions on the boosted cell; family and small-office use sits well inside the headroom, while a large public event approaching the ceiling should fall back to the main network rather than the repeater.

Frequently Asked Questions